How do I reset my Balboa hot tub control panel?

At 107¡F (approximately 41.7¡C), the spa should automatically reset. If spa does not reset, shut off the power to the spa. Standby Mode has been activated by pressing a button combination on the user panel. Press any button to leave Standby Mode and return to normal operation.

How do you change the mode on a Balboa hot tub?

The procedure for switching from one mode to another is different depending on the type of keypad installed on your hot tub. Keypads without a “Mode” button. Press “Temp”, then “Light” to switch to the next mode. Repeat the process until you reach the mode that you’re looking for.

How do I get my Balboa hot tub out of sleep mode?

On screen it will just state rest mode or whilst running filteration it will state “run” “pump” “for” “temp”. TO EXIT REST MODE:- Press Temp, then press light repeatedly until ‘MODE’ appears in the LCD. Toggle between READY and REST by pressing temp.

What mode should I run my hot tub?

Economy is a good setting for those who use the hot tub daily. The drop in temperature fluctuates during the year from minor or no temperature falls in the summer, to larger drops in the coldest part of winter.

Why is my hot tub control panel not working?

If the control panel is frozen or dead, you have to check if the problem is the control panel or the circuit board. Examine if there is moisture in the display. Check if there are cracked buttons or if a part is wet. If only a part is not working, look for error messages or blinking lights.

How do I fix my hot tub control panel?

No Display on Topside Control Panel

  1. Reset Spa Controller, power down and restart.
  2. Check for condensation under display glass.
  3. Check cable for crimps or any visible damage.
  4. Clean plug-in cable connections on both ends.
  5. Check power at Transformer on control circuit board.
  6. Check power at fuse on spa control circuit board.

What does the AUX button do on a Balboa hot tub?

Priming the Pumps Also, push the Pump 2 or “Aux” button, if you have a 2nd pump, to turn it on. The pumps will now be running in high-speed to facilitate priming. If the pumps have not primed after 2 minutes, and water is not flowing from the jets in the spa, do not allow the pumps to continue to run.

What causes a hot tub not to heat?

Low flow in your spa or hot tub is most commonly associated with a dirty spa filter. If your spa heater won’t heat, remove and clean the filter(s) to rule out a pressure or flow rate problem. Low water level, a clogged pump impeller, closed valves, clogged pipes, or blocked spa drain covers can also cause flow issues.

Should jets be on when heating hot tub?

Before covering your hot tub, make sure to turn on the jets as this will accelerate the pace of your hot tub’s heating. By running the jets, you’re allowing the heated water to be circulated and evenly distributed to all areas of the hot tub.

How long does it take a Balboa hot tub to heat up?

It will take less time to heat if it is warmer outside. If you want your hot tub to be 100 degrees, it will take 4 hours to reach it’s temperature. If you keep your hot tub cover on, you can shorten that time.

Should I put my hot tub in sleep mode?

Sleep Mode If you are going to be away for an extended period of time, it’s best to put your spa into this mode to save you some money on electricity costs. This mode will heat the spa up to within 20°F of the temperature set only during the filter cycle.

When should I put the hot tub in sleep mode?

Sleep : This works on the same basis as economy but when the hot tub filters , the heater will only operate when the drop in temperature is 10 degrees below the standard setting , so if your standard setting is 36 degrees, the heater when in sleep mode will only be activated when the temperature drops below 26 degrees.

How do I know if my control panel is bad in my hot tub?

Control Panel is Not Working If only a part is not working, look for error messages or blinking lights. As a first step, reset your breaker. If the problem persists, turn the breaker off and disconnect the panel to examine the circuit board. Turn the power on and check if the hot tub heats up or starts to filter.

How do I know if my hot tub control board is bad?

You should see 220 volts. If you do not, then the circuit board is faulty and will need to be replaced or sent to us for repair. If you do see 220 volts and it is not heating then the heating element is defective and will need to be replaced.

How do I know if my hot tub control panel is bad?

How do you get Balboa out of EC mode?

Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode. Press any “Cool”, “Warm”, or “Temp” Button to Exit Priming Mode.

https://www.youtube.com/watch?v=krWRuOr1Y28