How do you reset the tire pressure sensor on a 2008 Chevy Cobalt?

With RKE

  1. Turn the ignition key to the “ON” position without starting the engine.
  2. Press the Remote Keyless Entry (RKE) transmitter’s LOCK and UNLOCK buttons simultaneously for five seconds.
  3. Activate the TPMS sensor.
  4. Repeat the process for the passenger side front tire, passenger side rear tire, and the driver side rear tire.

How do you reset the tire pressure sensor on a Chevy Cobalt?

Turn your vehicle’s key to the “On” position without starting the vehicle. Push the TPMS reset button until the tire pressure light flashes three times, then let go. Start the car and wait for about 20 minutes for the tire pressure sensor to refresh.

How do you relearn a TPMS sensor?

Manual relearn procedure, Base Level DIC, 2015-2020:

  1. Confirm TPMS sensors are properly installed.
  2. Adjust tire pressures to placard value.
  3. Apply parking brake.
  4. Turn vehicle to ON/RUN.
  5. Push the trip odometer reset stem until Tire Pressure is displayed.
  6. Push and hold trip reset stem to begin the sensor matching process.

Where is the TPMS reset button on a 2010 Chevy Cobalt?

Turn ignition to the ON/RUN position with the engine OFF (not the ACC position) and lower the driver’s side window. Press the Vehicle Information button (located to the left or right of the instrument cluster) repeatedly until “LEARN TIRE PRESSURES” is displayed. Then press the checkmark button.

Do you need a TPMS relearn tool?

With the exception of some Chrysler and Mazda models that may be relearned to the vehicle via a driving procedure, a TPMS scan tool is required to complete the vehicle relearn procedure.

What are the most common GM TPMS relearn procedures?

The three types of relearn procedures are auto relearn, stationary (manual) and OBD.

How do I reset my Cobalt?

How to Reset Oil Life: Chevrolet Cobalt 2005-2010

  1. 1-Turn the ignition to run (second position)
  2. 2-Press the INFO button to scroll until the Oil Life displays.
  3. 3-Press the INFO and RESET (arrow) buttons at the same time to display OIL LIFE RESET.
  4. 4-Press and hold the ENTER (arrow) button until the cluster shows AKNOWLEDGED.

Does TPMS need to relearn after tire rotation?

These sensors take air pressure readings and send the data to your vehicle’s dashboard. Pros – They deliver accurate pressure readings; batteries can last up to 10 years; there is no need to reset them after tire rotation or inflation adjustments.

Do you have to reprogram TPMS sensors when rotating tires?

Once all of the tires are rotated, it’s time to reprogram the TPMS sensors. This will effectively tell your car which sensor is paired with which tire.

How do I reset the TPMs on a 2008 Chevy Cobalt?

If you have 2008 2009 2010 Chevrolet Cobalt, you can reset the TPMS by increasing or decreasing the tire pressure without tools. Follow these instructions to get started: Turn the ignition key to the “ON” position without starting the engine

How do I relearn the TPMs on my vehicle?

Starting with the LF tire, use a properly formatted TPMS scan tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, the horn will chirp twice signifying the relearn is complete. Turn the ignition to the OFF position.

What causes the Chevy Cobalt TPMS light to blink?

If you replacing a spare tire with a road tire containing the TPMS sensor on your Chevy Cobalt, the system will detect a malfunction and the low tire pressure warning light will blink. When that happens, the TPMS sensor reset process must be done.

How do I Pair my TPMs with my RKE?

Press the Remote Keyless Entry (RKE) transmitter’s LOCK and UNLOCK buttons simultaneously for five seconds The horn will sound twice and the TIRE LEARNING ACTIVE message will appear indicating the TPMS matching process has started.